Distributed by RNK Distributing
Quilters Select - Made Specifically for Quilters!
 
  • qs-1
  • qs-2
  • qs-9
  • qs-3
  • qs-4
  • qs-5
  • qs-6
  • qs-7
  • qs-8

Select Print and Piece AND Select Print and Piece Fuse Lite

Available in two versions:
Select Print and Piece & Select Print and Piece Fuse Lite

Select Print and Piece

Use for printing foundation or paper-pieced patterns. This fiber-based foundation won't perforate while stitching and supports detailed patterns. The fibers are partially water-soluble; simply dampen the stitching lines and they remove easily without distorting stitches!

Directions for Use and Care

For paper or foundation piecing:

  • If possible, set your printer’s paper feed settings to “Decorative or Heavy Paper.” If your printer does not have this setting, load only one sheet of Print & Piece at a time.
  • Copy or print your favorite foundation or paper-piecing pattern directly onto Print & Piece stabilizer.
  • Cover the numbered sections as directed with your favorite fabrics until the block is complete.
  • Remove the stabilizer: once the stitching is complete, lightly dampen only the stitching lines with a wet sponge or cotton swab – the stabilizer tears away gently without distorting the stitches!
  • You can alternately leave the stabilizer within the block completely. When the quilt is laundered, the watersoluble fibers will dissolve and the non-soluble fibers will leave behind a very subtle loft. Create a test block with this method before applying it to an entire quilt to make
    sure you are happy with the results!

For stabilizing decorative or satin stitches:

  • Place one layer of Print & Piece directly under fabric and stitch.
  • To remove the stabilizer, lightly dampen only the stitching with a sponge or cotton swab – the stabilizer will pull away without distorting delicate heirloom, satin or decorative stitches!

Washer and Dryer Safe

Cool water and low drying temperature recommended.

Press using a medium setting on your iron.

Size Available

QSPP-811
25 pieces 8½" x 11" printable sheets (21.59 cm x 27.9 cm)

Print & Piece Video: What is Fabric Print & Piece?

Select Print & Piece Resources

Select Print and Piece Fuse Lite

There are so many uses for this versatile product! It’s ideal for needle-turn appliqué patterns, and the sheerness makes tracing a snap. The 8½" x 11" pre-cut sheets are perfect for printing complex patterns with an ink jet printer. This fiber-based stabilizer gives solid yet soft support for detailed machine embellishments, including bold satin and heavy decorative stitches. The temporary fuse keeps fabrics from shifting or pulling while stitching or during the hooping process. The fibers of Select Print & Piece Fuse Lite are partially water-soluble; simply dampen the stitching lines and they remove easily without distorting stitches!

Directions for Use and Care

Directions for use on printers:

  • ONLY to be used with an ink jet printer, DO NOT USE IN LASER PRINTER.
  • Load sheets one at a time.  Loading multiple sheets may cause the ink jet printer to jam and could damage the printer.

Directions for general use as a stabilizer for embellishment:

  • Heat iron to silk setting (low).
  • Position the fusible side of Print & Piece Fuse Lite over the wrong side of the fabric.
  • Cover the stabilizer with a cotton pressing cloth or piece of muslin. It is also OK to press from the fabric side instead of the stabilizer side.*
  • Press with the iron with an up-and-down motion, not side-to-side. If a bond is not achieved, slightly increase your iron temperature and try again.**
  • Once stitching is complete, slightly dampen the stitching line and pull away the stabilizer.

*Remember that all irons heat differently. We recommend testing on scrap fabric before beginning your project. 

**The fusible coating on the stabilizer was designed to be temporary. If the iron temperature used is too hot, the bond may become permanent.

Directions for needle turn appliqué:

  • Print or trace the image on to the non-fusible side of the stabilizer.
  • Trim away the excess stabilizer by cutting directly on the lines.
  • Fuse the stabilizer/image onto the wrong side of the fabric being used for the appliqué.
  • Trim the fabric to within a generous ¼˝ of the stabilizer/ image.
  • Use a fabric-safe glue stick and lightly coat the edge of the stabilizer/image.
  • Turn the fabric so that it sticks to the glue.
  • The appliqué is now ready to be stitched into place on your quilt block, garment or home dec project!
  • There is no need to remove the stabilizer from behind the appliqué: when washed, half of the fibers will dissipate; the other fibers will create a slight loft under the appliqué.

Washer and Dryer Safe

Cool water and low drying temperature recommended.

Press using a medium setting on your iron.

Size Available

QSPPFL-811
25 pieces 8½" x 11" printable sheets (21.59 cm x 27.9 cm)

QSPPFL-2010
20" x 10 yards (50.8 cm x 9.14 m)

Print & Piece Fuse Lite Video: What is Print & Piece Fuse Lite?

Select Print & Piece Fuse Lite Resources

 

Add Review

This form is for REVIEWS ONLY! For general inquiries, customer service or support please contact us!

You are reviewing: Select Print and Piece AND Select Print and Piece Fuse Lite
Rate this product*:
Rating
Review:

Please note: Your email address will not be shared online or with any vendors nor will it be added to our or any other mailing list. Your email is only being collected in the event that your review indicates you require product support.

 

Customer Reviews

Review by 
(posted on )
Displaying 0 to 0 (of 0 customer reviews)